Search results

Create the page "Lye" on this wiki!

• Amor fati's Compendium for the Extraction of Jurema
  ...tensive A/B teks that notoriously require at least a hazardous base like [[lye]]. Then we will consider the use of various alternative solvents, typicall
  9 KB (1,344 words) - 21:55, 31 January 2012
• The Tao of Rue Extraction
  {{ShowInfo|[[Image:Note_error.png]]|'''Warning:'''|Lye can be very dangerous if not handled with RESPECT. Always wear gloves and p ...he brew, we'll make a lye or sodium carbonate solution. I don't mind using lye in this step because we're going to filter our alks and then redissolve the
  15 KB (2,669 words) - 04:12, 20 August 2014
• STC - Dream Weaver's tek
  * 32oz glass mason jars (4 should suffice) (I was told lye can eat the glass away so please be careful of this! and be careful when yo ... a minimum 1:1 ratio to MHRB (I have a huge quantity so i use 150-200grams lye per 100 grams mimosa)
  7 KB (1,359 words) - 18:54, 12 June 2012
• Cybs' Hybrid ATB 'Salt' Tek
  * Lye (Caustic Soda) ...us...do not get any on your skin or eyes. Avoid inhaling fumes when mixing lye with water.
  17 KB (2,773 words) - 15:14, 15 January 2023
• Kash's A/B Mescaline Extraction
  *50g NaOH (Lye)
  9 KB (1,450 words) - 02:13, 28 July 2018
• Combination of TEKs
  1: 40 grams Caustic Soda ( Lye). When scaling up this TEK, use 15ml water and one gram of Caustic Soda for ...lite - 1 ml of Shellite is used for each 15 ml of water used to create the lye solution for extraction - so in this case 40 mls of Shellite per extraction
  11 KB (1,908 words) - 02:40, 25 April 2014
• User talk:TopEndDMT
  1: 40 grams Caustic Soda ( Lye). When scaling up this TEK, use 15ml water and one gram of Caustic Soda for ...lite - 1 ml of Shellite is used for each 15 ml of water used to create the lye solution for extraction - so in this case 40 mls of Shellite per extraction
  10 KB (1,813 words) - 17:30, 24 April 2014
• The Wanderer's Tek
  ...ry volatile material so be very careful with it. Add very small amounts of lye to the water and stir it well. Test the pH often. You are aiming for a pH o ...your extraction. You are trying to reach a pH level of 12. Keep adding the lye water to the extraction until you reach this pH, but stir well to ensure an
  10 KB (1,931 words) - 11:40, 9 January 2016
• Talk:Noman's tek
  I typically start by mixing my distilled water and lye with the finely ground bark, add my NAPTHA. I do a couple minutes of mixin
  2 KB (454 words) - 16:52, 16 February 2020
• User talk:ThatOneGuy121212
  SWIM has 2 big mason jars, gloves, mask, naptha, lye, ACRB, Glass baster SWIM poured 250ml hot water in jar and slowly added 100g lye, he then added 100g ACRB, Shook like crazy 2mins at a time over over an hr
  2 KB (319 words) - 11:23, 25 April 2019
• User talk:Zatoichi
  I am looking for alternative to lye, and want to be sure any substitutions do not produce unwanted bi-products.
  678 B (120 words) - 02:04, 15 October 2019
• User talk:Justamessenger
  5. Measure 500ml of hot water, weigh 60 grams of lye, stir 30g into H20 at a time, add to flask. 5. 60 grams Lye
  2 KB (238 words) - 19:39, 18 March 2020
• Freakinkat
  ...k of *(note will reference and link later)* which involved muraría acid, lye, naphtha, sodium carbonate, distilled water, vinegar for neutralizing and o
  1 KB (265 words) - 10:17, 17 January 2021
• Chilled Acetone with IPA and Naphtha
  ... and shake vigorously for a few minutes. Solution will warm up slightly as lye dissolves and will quickly go from red, to milky, to dark red. .... 3). If separation is not complete after 30 minutes, mix in another 5g of lye and try again.
  11 KB (1,808 words) - 14:22, 11 July 2022
• User talk:Kez
  Usually 100g bark 1.5l water100g table salt 100ml white vinager 100g lye 100ml naphtha ...just proportions ie. 300 bark 4.5 l water 300 salt Epsom?? 300ml vin 300mg lye 300ml naph
  464 B (86 words) - 09:54, 27 August 2021