Difference between revisions of "The Inspirator"

Revision as of 21:34, 22 January 2010

Note:

This page tracks the development of The Inspirator[1]. The content is to remain accurate as such.

The Inspirator is considered by its creator to be the criterion of efficiency for vaporizing spice, and to be a cheap and effective method of achieving sufficiently cool, full, measured doses. The device is inspired in part by The Machine but operates by convection heating, rather than conduction.

Procedure for Construction

Materials Required

Equipment: Butane Torch (same one that will be used for vaporization) Glass Dropper Stem (either from a pharmacy OTC or an online vendor) Ceramic Fiber (in any form, often found as blankets) 1 Round Metal Screen or Faucet Aerator (as long as the metal doesn't burn or melt with the use of a butane torch) A Thin Metal Rod (even a paper clip would probably work) Safety Pin (long enough to punch holes through the plug) Pliers Rubber Gasket and/or Latex Tubing

The Inspirator

Close up of the heat intake.

An alternative design w/ copper mesh.

1. Carefully crush the nozzle of the dropper stem with pliers, leaving a slight portion of the nozzle's curve.
   • be sure to wash out any lingering pieces of glass.
2. Melt the broken end of the stem with a torch so that the sharp edges are dulled and any cracks sealed.
3. Cut a segment of ceramic fiber, and use a thin metal rod to stuff it down toward the nozzle-end snuggly, and so that a part of the ceramic is exposed out of the heat intake.
4. Ensure that the screen is heat resistant by applying direct flame with the torch, and if smoke emits, continue to burn until no more can be observed.
   • alternatively, a small metal mesh plug can be prepared from steel or copper scrub-pad in the same manner.
   • this is the absolute highest temperature this piece will ever reach and will remain inert while in use.
5. After it has cooled, use a chopstick or another cylindrical device thin enough to fit the inside of the dropper stem to apply pressure to the center of the screen while bending the edges up and around the device to mold it into a form that will fit snuggly in the stem.
6. Carefully push the screen as snuggly as possible atop the ceramic fiber plug in the piece, working edges down between the glass and the plug.
7. Fit two gaskets on the stem far enough from the plug to avoid heat but far enough from the other end to provide a stable stem.
   • alternatively and more cheaply, a small section of latex tubing could be rolled or folded into a ring around the stem to serve the same purpose.
8. Use a safety pin to punch several holes all the way through the middle of the ceramic plug to the screen while maintaining one large central whole as the primary intake to ensure adequate airflow.
   • there should be some amount of pressure but no strain on the draw.
   • airflow is the key factor in ensuring the quality and effectiveness of the device.

Administration.

1. Place product into the open end of the stem and stuff down to the screen with a thin rod.
2. Feather the glass with a torch until the product melts into the screen.
3. Insert the stem into a bubbler as a bowl, with the open end in.
4. Use a torch to apply heat to the exposed ceramic portion of the plug while drawing air through the bubbler.
   • keeping some distance with the torch is recommended to avoiding burning or overheating.
5. Only apply heat until a decent amount of vapor can be observed in the chamber, carb the bubbler immediately but briefly, and continue to apply heat and inhale in the same manner.
   • once the device reaches a sufficient temperature, it will give off vapor rapidly and will not necessarily require continued heat application, but continue to heat periodically during the draw to ensure complete vaporization.

Seated in a bubbler.

Loading the device.

Use with an Improvised Labware Bubbler

NOTE Though a slightly different design is pictured, this design is to be used in the same manner. The mouthpiece is a longer dropper tube (Pasteur pipette) connected to the nozzle of the vacuum flask by another segment of latex tubing. The segment of latex on the top of the inlet is folded over itself to make a wide even rim to facilitate a proper seal with the glass rim of the dropper stem when held in place.

Notes on Effective Use and Maintenance

for Cleaning The Inspirator

Attach a chemically resistant dropper bulb to the open end of the stem. Prepare a flask of cleaning solvent (IPA or acetone work best). Draw in the solvent and squirt out through the plug until sufficiently clean. actives may potentially be salvaged from cleaning solvent collected over time. Scrub with a q-tip. Carefully blow out remaining solvent. Feather the piece with a torch to aid in evaporating solvent and carefully apply the flame to the tip in order to burn any residual solvent Scrub out moisture with the other end of the q-tip. Ensure the absence of residual solvent prior to use by smell and further flame application.

• A handy method for storing the piece would be to cap the nozzle end with the dropper bulb in order to protect from breakage and keep track of the bulb to use when cleaning.
• A second gasket generally makes the piece safer to handle--especially if used as a pull stem--while the other provides a seal.
• For group sessions, it would be easiest to prepare an individual piece for each person so that dosage can be more easily regulated.
• When handling the piece after heating, handle by the gasket and avoid any part of the heated portion of the glass coming into any contact with hard surfaces.
• A good way to cool down a stem is to roll it rapidly between the palms, drawing the heat off the glass with one's hands.
• If the the nozzle end of the piece breaks off at any point, carefully push the plug to the other end of the piece when it has sufficiently cooled, heat the sharp edges until dulled, and push the plug back into place firmly, with a finger in place causing the plug to mushroom slightly until it fits snugly in place.
• Ensure adequate airflow through the piece by poking holes in the plug with a safety pin.
• Develop a relationship with the device.

Appendices

Special Thanks:

• To Warrensaged for pioneering the use of a machine-style bowl with a bubbler.
• To q21q21 and Bumber for inspiring the development of this method.

Reference

1. ↑ Presenting The Inspirator (Ceramic Fiber to Replace Metal Mesh in "The Machine") by amor_fati