Difference between revisions of "Machine-Style Bubbler Piece"

From DMT-Nexus Wiki
Jump to: navigation, search
(created page for transclusion)
 
(expanded article)
Line 6: Line 6:
 
|the Improvisation of the Bubbler Variation of "[[The Machine]]"
 
|the Improvisation of the Bubbler Variation of "[[The Machine]]"
 
|
 
|
−
* This variation can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers.
+
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|This variation can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers, though smaller bubblers are often found most preferable.
−
** ''smaller bubblers are often found most preferrable.''
+
|0px
−
* One need only to follow steps 2-4 of the standard variation though in application to the bowl of a bubbler rather than an improvised glass-piece.
+
|
−
* The water in the bubbler acts only as a heat-sink and will not absorb a significant if any amount of product, as the freebase product is not very soluble in water.
+
−
* The use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.
+
 
}}
 
}}
 +
[[Image:Machine-Style Bubbler Bowl.jpg|thumb|right|A Machine-Style Bubbler Bowl being loaded.]]
 +
# Prepare a plug made of metal mesh by cutting a piece of an excess of the appropriate size to fit in the bowl.
 +
#* ''Stainless steel and copper of a coarse mesh are preferable, as they do not tend to burn at the temperatures needed for vaporization.''
 +
# Using pliers to hold the cutting, use a torch to thoroughly burn off any machine oil or coatings found on the mesh.
 +
#* ''Perform this step until no more smoke can be observed emanating from the cutting.''
 +
# Allow to cool and roll the cutting tight enough to fit in the bowl.
 +
#* ''The plug needs to be tight enough to suspend it in the opening but not so tight as to block air passage.''
 +
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|The water in the bubbler acts only as a heat-sink and will not absorb a significant if any amount of product, as the freebase product is not very soluble in water; however, the use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.
 +
|0px
 +
|
 +
}}
 +
}}
 +
 +
Notes on Administration:
 +
:* To load, simply place a measured dose directly on top of the plug and carefully melt into the plug by feathering with a flame or other heat source.
 +
:* Though a standard lighter will work for vaporizing if used carefully, a torch will ensure a fuller dose.
  
 
Alternative Machine-Style Bubbler Pieces:
 
Alternative Machine-Style Bubbler Pieces:

Revision as of 21:09, 21 January 2010

Note error.png Note: This page has been transcluded to The Nexian DMT Handbook under the Machine-Style Bubbler Piece section or other locations within or without the handbook. Please markup in consideration of this. The top section header is to remain in place as a reference for subsequent section headers and to allow easy editing directly from the handbook.
Machine-Style Bubbler Bowl
the Improvisation of the Bubbler Variation of "The Machine" Cog.png
NOTE Information.png
This variation can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers, though smaller bubblers are often found most preferable.
A Machine-Style Bubbler Bowl being loaded.
  1. Prepare a plug made of metal mesh by cutting a piece of an excess of the appropriate size to fit in the bowl.
    • Stainless steel and copper of a coarse mesh are preferable, as they do not tend to burn at the temperatures needed for vaporization.
  2. Using pliers to hold the cutting, use a torch to thoroughly burn off any machine oil or coatings found on the mesh.
    • Perform this step until no more smoke can be observed emanating from the cutting.
  3. Allow to cool and roll the cutting tight enough to fit in the bowl.
    • The plug needs to be tight enough to suspend it in the opening but not so tight as to block air passage.
NOTE Information.png
The water in the bubbler acts only as a heat-sink and will not absorb a significant if any amount of product, as the freebase product is not very soluble in water; however, the use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.


Notes on Administration:

  • To load, simply place a measured dose directly on top of the plug and carefully melt into the plug by feathering with a flame or other heat source.
  • Though a standard lighter will work for vaporizing if used carefully, a torch will ensure a fuller dose.

Alternative Machine-Style Bubbler Pieces:

The Mini-Machine Bubbler Stem
The Inspirator


Reference
Retrieved from "https://wiki.dmt-nexus.me/w/index.php?title=Machine-Style_Bubbler_Piece&oldid=2383"