Difference between revisions of "The Inspirator mkII"

Latest revision as of 20:57, 31 January 2012

Note:

This page tracks the development of The Inspirator mkII.[1] The content is to remain accurate as such.

For further reference and discussion, see references:[2]

The Inspirator mkII is considered by its designer to be the criterion of efficiency for vaporizing spice, and to be a cheap and effective method of achieving sufficiently cool, full, measured doses. The device is inspired in part by The Machine but operates by convection heating--diffusing the heat through a ceramic heat-sink, in turn heating the airflow--rather than heating by conduction. This design was the final evolution of The Mini-Machine Bubbler Stem and the original version of The Inspirator.

This particular model of the Inspirator utilizes a removable heating element to enable spice to be loaded into the top-side of the bowl, preventing the occurrence of run-off or drip. The position of the element in relation to the plug also helps prevent overheating or burning by conduction, while the element itself serves to protect from exposure to the flame.

Contents 1 Procedure for Construction 1.1 Constructing the Heating Element 1.2 Constructing the Bowl 1.3 Going Further for Changa and Enhanced Versatility 2 Effective Use and Maintenance 3 Appendices 3.1 Special Thanks 3.2 Reference	The Inspirator mkII	Materials Required Equipment: Glass Dropper Stem (either from a pharmacy OTC or an online vendor) Glass Dropper Bottle (for cleaning and preserving the piece) Ceramic Fiber (optional but preferable, in any form) Please use SuperWool 607 HT for health considerations. 1 Round Metal Screen or Faucet Aerator (as long as the metal doesn't burn or melt with the use of a butane torch) Chopsticks (preferably the cheap, skewer-type) Rubber Gasket and/or Rolled Up Latex Tubing Tubing of Same Diameter as Dropper Stem (a broken dropper, as pictured, though a sturdier material is preferable)
Procedure for Construction Note:  Though this design is thought to minimize the possibility of exposure, SuperWool 607 HT should be used for health considerations, as ceramic fiber can be hazardous to the repiratory system. Safety Note Always preheat screens or other metal materials to be heated directly with a torch before use so as to ensure any potentially hazardous coatings have been burned off if present. The Core of the Heating Element The Shell of the Heating Element Constructing the Heating Element For the core: Place ceramic fiber onto a screen. If ceramic fiber is not available or desired, two screens may be rolled together to compensate for the volume. Fold the screen to clasp the fiber. Begin to roll the screen by folding an end. Roll the screen tightly. For the shell: Firmly hold the tip of a chopstick in the middle of the screen. Bend the sides up around the tip. Bend the ends ups while holding the sides in place to cradle the tip of the chopstick. Place the core in the shell to create the element. Note that it may be necessary to place a small amount of ceramic fiber in the bottom of the shell, under the core, to achive a large enough element that it won't slip into the bowl when in use. Use discretion; it can always be re-worked.

Condensing the element in a broken dropper stem.

The finished heating element

Condensing the element in an eraser cap w/ the end bored out.

Final Touches:

To form the Element into a single unit that will fit snugly into the the bowl, use a tube of the same diameter as the dropper stem to be used and two chopsticks to press it into shape. A broken dropper stem is pictured, but something sturdier and less hazardous would be ideal--like a pen tube or pipe. The element could also be rolled around between fingertips to help reduce the springiness it may have when attempting to insert into the end of the bowl or dropper stem. It should fit snugly without slipping in or springing out.

When in place, the element will permit air passage through and around itself, into the bowl, and since the element itself will absorb the heat application of the torch, it will in turn heat the air flow while protecting the contents of the bowl from the flame.

Variations in Design
As ceramic fiber may not be readily available, it may be omitted and replaced with a second screen rolled up for the core for the "Night Elf" variation in technique and design, vice the "Spiceliner" variation which utilizes ceramic fiber.

Placement of the the plug and the element in the dropper stem.

Constructing the Bowl

The plug for the bowl may be constructed in much the same manner as the heating element, but without the ceramic, rolling two screens together for the core instead. The plug should be inserted, shell first, into the stem a centimeter or so from the opening to provide space to load the vaporizing agent and protect it from overheating by keeping distance from the element. The plug will provide a bottom for the bowl, into which the agent may be melted and prepped for inspiration.

Gaskets are then installed using the sort commonly found for use in plumbing, or else made from rolled up sections latex tubing. The gaskets must serve two purposes: A cool grip for carbing (if using pull-stem) or general handling and most importantly, a seal for the bubbler. These will be removed along with the element when in storage if using a dropper bottle as recommended, so a separate container for those would be ideal.

Going Further for Changa and Enhanced Versatility

Sharp, jagged edges after clipping.

Crushing the tip with pliers.

Melting the tip w/ butane torch.

Plunging down.

Plunging back up into place.

Clipping the Tip:

A very simple process, but be safe and take the appropriate protective measures! Over a garbage can, sink or what have you, grab the tip of the dropper firmly with pliers. Apply slow, steady pressure until the tip shatters. Pieces of glass will tend to fly out a ways, so shield eyes, sweep, wipe surfaces with a damp paper towel or whatever needs to be done to protect oneself and others from debris. Wash debris from the piece with running water.

Final product after melting the tip.

Melting the Edges:

There will be sharp edges and cracks where the piece was broken, so melting will be necessary to ensure the safety and integrity of the piece.

1. Suspend the tube as deemed fit to avoid burning oneself.
2. With a butane torch, apply the flame right to the end where there are sharp jagged edges and cracks.
3. The glass will glow red, cracks will seal, and edges will round off.
4. The hole will likely close a bit, so if necessary, push a metal rod through while heating.
   • This end must be accessible in order to position the plug wherever needed.

Advantage and Exploitation of Accessibility:

The only way to properly vaporize--avoiding combustion or overheating--from changa, enhanced leaf, a leaf-bed or even straight spice, for that matter, is to position the plug so that the material to be vaporized is a safe distance from the heating element. Volatiles (pure actives, typically) should usually be at least 0.5cm, while combustibles (enhanced leaf or some impure actives) should be positioned more than 1cm from the heating element. In some cases, drippage or runoff may occur; in such cases, it can be retrieved by simply plunging the plug all the way down to the tip, then back up into place.

Effective Use and Maintenance

Storage, preservation, and cleaning:

1. Fill a dropper bottle with IPA.
2. Install the dropper stem as per normal and pipette the IPA repeatedly.
3. Fill the stem before sealing away for storage.

• Before use, the pipetting process may be repeated, followed by a rinse with running water and blow drying the piece by mouth.
• While proper use with a pure product will yield very little to clean, repeated use may result in precipitation beyond the plug.

Heat application and inspiration:

1. Load the agent all the way down to the plug.
   • Optionally, feather the glass around the plug with a torch lightly to melt the agent into the plug.
2. Place the element snugly into the open end of the bowl.
3. Apply flame only while inhaling, applying enough to cause the element to glow, and applying frequently enough to attain constant vapor production.
   • 'Prolonged application of the flame to the heating element may result in cracking of the glass, as well as general overheating in some cases. To avoid this, feather along the tip in a tight circular motion removing the flame periodically, gauging the effectiveness by repeatedly quickly pulling the carb. The element may eventually take on enough heat to continue producing vapor without the flame.'
   • For the "Spiceliner" variation, using ceramic fiber, the flame may come into contact with the heating element and at any angle with little trouble.
   • For the "Night Elf" variation, using only steel screens, direct heating in line with the bowl should be avoided, and direct contact with the heating element and the torch should not be made.

Note on Dosage
30-40mg spice should be sufficient for a breakthrough if accomplished in a single toke. The level of effects attained at this dosage is adequate for gauging the effectiveness of technique.

Tips and Tricks:

• Keep a kit of spare parts and extra devices handy: Not only is it quite possible to break a device or lose any of the smaller parts of this design, but it would be handy to have multiples for guests.
• Besides storing the device in a dropper bottle, the dropper bulb could be used as cap to seal the end of the piece, containing the heat element as well as possibly any loose contents.
• The Inspirator may also be used without a bubbler for portability, stealth, and resource considerations.

Appendices

Special Thanks

• To Warrensaged for pioneering the use of a machine-style bowl with a bubbler.^[3]
• To q21q21 and Bumber for inspiring the development of the progenitor of this method.^[4]

• To OpeningPandorasBox for "The Key," which helped to inspire the development of this device.^[5][6]

Reference

1. ↑ The Inspirator mkII: a DIY convection heated vaporizer for use w/ bubblers by amor_fati
2. ↑ Suggestion for vaporization--thoughts from the nursery?
3. ↑ Bubbler Bowl Variation of "The Machine"
4. ↑ The Mini-Machine Bubbler Stem
5. ↑ The Key - Portable $5 Vaporizer - Assembly Instructions
6. ↑ The Key V2 - Water Pipe Vaporizer