Difference between revisions of "The Inspirator mkII"

From DMT-Nexus Wiki
Jump to: navigation, search
m
(stylization)
Line 19: Line 19:
 
This particular model of [[the Inspirator]] utilizes a removable heating element to enable [[spice]] to be loaded into the top-side of the bowl, preventing the occurrence of run-off or drip.  The position of the element in relation to the plug also helps prevent overheating or burning by convection, while the element itself serves to protect from exposure to the flame.
 
This particular model of [[the Inspirator]] utilizes a removable heating element to enable [[spice]] to be loaded into the top-side of the bowl, preventing the occurrence of run-off or drip.  The position of the element in relation to the plug also helps prevent overheating or burning by convection, while the element itself serves to protect from exposure to the flame.
  
 +
{|
 +
|-
 +
|valign="top"|
 +
__TOC__
 +
|valign="top" align="center"|
 +
[[Image:The Inspirator mkII.JPG|thumb|left|250px|'''''The Inspirator mkII''''']]
 +
|rowspan="2" valign="top"|
 
{{materials_list
 
{{materials_list
 
|
 
|
Line 33: Line 40:
 
* Tubing of Same Diameter as Dropper Stem (a broken dropper, as pictured, though a sturdier material is preferable)
 
* Tubing of Same Diameter as Dropper Stem (a broken dropper, as pictured, though a sturdier material is preferable)
 
}}
 
}}
 
+
|-
 +
|colspan="2" valign="top"|
 
===== Procedure for Construction =====
 
===== Procedure for Construction =====
 
{|
 
{|
Line 53: Line 61:
 
# Place the core in the shell to create the element.
 
# Place the core in the shell to create the element.
 
#* Note that it may be necessary to place a small amount of ceramic fiber in the bottom of the shell, under the core, to achive a large enough element that it won't slip into the bowl when in use.  Use discretion; it can always be re-worked.
 
#* Note that it may be necessary to place a small amount of ceramic fiber in the bottom of the shell, under the core, to achive a large enough element that it won't slip into the bowl when in use.  Use discretion; it can always be re-worked.
 +
|}
 
|}
 
|}
 
[[Image:Element condensing.JPG|thumb|left|250px|Condensing the element in a broken dropper stem.]]
 
[[Image:Element condensing.JPG|thumb|left|250px|Condensing the element in a broken dropper stem.]]

Revision as of 10:46, 24 February 2011

Note error.png Note: This page tracks the development of The Inspirator mkII[1]. The content is to remain accurate as such.


in·spi·ra·tor (ĭn'spə-rā'tər) n.

  1. A device, such as a respirator or inhaler, by which a gas, vapor, or air is drawn in.
  2. One who inspires or motivates others.

[From Late Latin, from inspirare 'to inspire' (from in- + spirare 'to breathe') + -tor; cognate with, and possibly derived via, English or German]


The Inspirator mkII is considered by its designer to be the criterion of efficiency for vaporizing spice, and to be a cheap and effective method of achieving sufficiently cool, full, measured doses. The device is inspired in part by The Machine but operates by convection heating--diffusing the heat through a ceramic heat-sink, in turn heating the airflow--rather than heating by conduction. This design was the final evolution of The Mini-Machine Bubbler Stem and the original version of The Inspirator.

This particular model of the Inspirator utilizes a removable heating element to enable spice to be loaded into the top-side of the bowl, preventing the occurrence of run-off or drip. The position of the element in relation to the plug also helps prevent overheating or burning by convection, while the element itself serves to protect from exposure to the flame.

The Inspirator mkII
Materials Required Checklist.png
Equipment:
NSPRTRmkII materials.JPG
  • Glass Dropper Stem (either from a pharmacy OTC or an online vendor)
  • Glass Dropper Bottle (for cleaning and preserving the piece)
  • Ceramic Fiber (optional but preferable, in any form)
  • 1 Round Metal Screen or Faucet Aerator (as long as the metal doesn't burn or melt with the use of a butane torch)
  • Chopsticks (preferably the cheap, skewer-type)
  • Rubber Gasket and/or Rolled Up Latex Tubing
  • Tubing of Same Diameter as Dropper Stem (a broken dropper, as pictured, though a sturdier material is preferable)


Procedure for Construction
The Core of the Heating Element
The Shell of the Heating Element
Constructing the heating element
For the core:
  1. Place ceramic fiber onto a screen.
    • If ceramic fiber is not available or desired, two screens may be rolled together to compensate for the volume.
  2. Fold the screen to clasp the fiber.
  3. Begin to roll the screen by folding an end.
  4. Roll the screen tightly.
For the shell:
  1. Firmly hold the tip of a chopstick in the middle of the screen.
  2. Bend the sides up around the tip.
  3. Bend the ends ups while holding the sides in place to cradle the tip of the chopstick.
  4. Place the core in the shell to create the element.
    • Note that it may be necessary to place a small amount of ceramic fiber in the bottom of the shell, under the core, to achive a large enough element that it won't slip into the bowl when in use. Use discretion; it can always be re-worked.
Condensing the element in a broken dropper stem.
The finished heating element
Final Touches:

To form the Element into a single unit that will fit snugly into the the bowl, use a tube of the same diameter as the dropper stem to be used and two chopsticks to press it into shape. A broken dropper stem is pictured, but something sturdier and less hazardous would be ideal--like a pen tube or pipe. The element could also be rolled around between fingertips to help reduce the springiness it may have when attempting to insert into the end of the bowl or dropper stem. It should fit snugly without slipping in or springing out.

When in place, the element will permit air passage through and around itself, into the bowl, and since the element itself will absorb the heat application of the torch, it will in turn heat the air flow while protecting the contents of the bowl from the flame.



Placement of the the plug and the element in the dropper stem.
Inspirator, removed element, and dropper bottle with IPA for storage, cleaning and preservation.
Constructing the Bowl

The plug for the bowl may be constructed in much the same manner as the heating element, but without the ceramic, rolling two screens together for the core instead. The plug should be inserted, shell first, into the stem a centimeter or so from the opening to provide space to load the vaporizing agent and protect it from overheating by keeping distance from the element. The plug will provide a bottom for the bowl, into which the agent may be melted and prepped for inspiration.

Gaskets are then installed using the sort commonly found for use in plumbing, or else made from rolled up sections latex tubing. The gaskets must serve two purposes: A cool grip for carbing (if using pull-stem) and most importantly, a seal for the bubbler. These will be removed along with the element when in storage if using a dropper bottle as recommended, so a separate container for those would be ideal.



Effective Use and Maintenance
Storage, preservation, and cleaning:
  1. Fill a dropper bottle with IPA.
  2. Install the dropper stem as per normal and pipette the IPA repeatedly.
  3. Fill the stem before sealing away for storage.
  • Before use, the pipetting process may be repeated, followed by a rinse with preferably warm water and blow drying the piece by mouth.
  • While proper use will yield very little to clean, repeated use may result in precipitation beyond the plug.
Heat application and inspiration:
  1. Load the agent all the way down to the plug.
  2. Feather the glass around the plug with a torch lightly to melt the agent into the plug.
  3. Place the element snugly into the open end of the bowl.
  4. Apply flame only while inhaling, applying enough to cause the element to glow, and applying frequently enough to attain constant vapor production.
  • 30-40mg spice should be sufficient for a breakthrough if accomplished in a single toke.


Appendices
Special Thanks
  • To Warrensaged for pioneering the use of a machine-style bowl with a bubbler.[2]
  • To q21q21 and Bumber for inspiring the development of the progenitor of this method.[3]
  • To OpeningPandorasBox for "The Key," which helped to inspire the development of this device.[4][5]
Reference
  1. The Inspirator mkII: a DIY convection heated vaporizer for use w/ bubblers by amor_fati
  2. Bubbler Bowl Variation of "The Machine"
  3. The Mini-Machine Bubbler Stem
  4. The Key - Portable $5 Vaporizer - Assembly Instructions
  5. The Key V2 - Water Pipe Vaporizer