Q21Q21's Vinegar/Lime A/B Extraction Tek
 |
Note: | This page is a transcription of Q21Q21's Vinegar/Lime A/B *NO LYE/NO FUNNEL/NO FUSS* Tek[1]. The content is to remain accurate as such. |
Although SWIM has heard of others doing teks very similar than this and highly doubts any aspect of this tek is "new"... he felt like putting it together with pics and detailed info into a tek, which required a name and thus put his.
| Materials Required |  |
|---|---|
Source Material:
|
|
Solvents:
|
|
Reagents/Desiccants:
|
|
Equipment:
Useful Tools:
|
The only 2 materials that aren't in 99% of household are:
1: Lime/Pickling Lime/Garden Lime/Cal/Ca(OH)2. It is a powerful base that is actually food safe. Although like anything eating a lot of it will upset your body, but there isn't anything but traces of traces in the final product.
There dose seem to be a large amount of problems obtaining lime though. If it isn't at your local hardware store or ethnic grocery then you may have to look online. SWIM found a few sites that look like they would work. 5lbs (A LOT) for ~$10 plus shipping, ships worldwide 1 lb for $4.47 plus shipping, USA only
If those don't seem to work then googling "pickling lime" would be the next step. SWIM assures you the effort used to get the lime will far pay off with the ease, speed, efficiency AND SAFETY of the tek.
2: Naptha petroleum. A non-polar solvent and the only non-food-safe ingredient, though it's toxicity is quite benign. The LD50 for naptha is stated as 8000-20000mg/Kg while the LD50 for DMT is 60-110mg/Kg. Heck the LD50 for Vitamin A is 1510-2570mg/Kg and Vitamin B is 560mg/Kg.
Plus 2 things: 1. it evaporates cleanly without a trace in a couple hours 2. When burned it produces only WATER and CARBON DIOXIDE, that is why using it as a lighter fuel is safe.
Anyway, it is simply lighter fluid which most house have around, but you need one that doesn't have any nasty additives.
If you are in the US then VM+P Naptha is your choice. If you are in Canada then Ronsonol Lighter Fluid or Escort Camp Fuel are your choices. If you can't find either then buy some lighter fluid test it: 1.Pour a little on a surface (SWIM used blank Cds) 2.Wait an hour or two for it to evaporate. If it smells or looks like anything other than a blank and dry CD then the lighter fluid won't work.
If you still don't want to work with naptha, there is a food safe alternative tek using d-limonone. The tek will direct you when to scroll down for instructions on the alternative tek
(what your product will look like If you follow the tek)
[whitejn.jpg]
Contents
Procedure
Preparation:
[bowls.jpg]
The picture is not of the first step but does illustrate the set-up of the bowls.
-If your MHRB isn't powdered, use a blender to cut it in powder/fibers as small as possible
-Prepare Chopsticks, vinegar, lime and always have a source of boiling water or near-boiling water nearby.
-Ready 2 same-size bowls/containers that fit together.
-Boil some tap water and fill one of your bowls 1-2 inches with it, then place the second bowl on top. It is simply used as a gentle heat source instead of heating over a stove.
Note: The bottom water is never added to the top, only used as a warming bath.
Acidification:
This step is utilizing the vinegar (acetic acid) to change the DMT-tannate molecules contained in the bark into DMT acetate and in the process extract them into the vinegar.
[acidsoak.jpg]
-Take 10-150g powdered MHRB and place in your top bowl, the tek works best if the amount doesn't fill the container more than an inch or two.
- Yo can either heat some vinegar in kettle before adding it to the bark, or let the vinegar/bark mix heat up slowly via the water bath underneath. In either case it is 2ml for each gram of bark used. (IE: 200ml vinegar for 100g MHRB) A 50/50 mix of water and vinegar could probably work just as well, but vinegar is cheap so SWIM usually just uses it straight (Hydrochloric acid also works, simply add same amount of H2O then add several drops until the bark turns dark red)
-Stir the bark (chopstick works VERY well) until it is all wet. The bark should turn very red and be slightly watery.
-Stir several times as the bark is let to sit for 30-60 minutes, more time won't hurt though.
-The bottom water likely has cooled somewhat by now. So separate the top and bottom bowls and replace the now-cooled bottom water with boiling water then place the bowl with the bark-mush on top again. Just to keep it warm
NOTE: if you skip this step the tek will still work, though it will require frequent mixing over a minimum of 2 days before a yield of >50% is achieved. Translation: This step isn't a necessity, but extremely useful. (Just buy the vinegar for 2 bucks)
Basification:
This process utilizes the alkalinity of the lime to freebase the DMT acetate into DMT freebase which is not water soluble, but is soluble in naptha
[crust.jpg]
-Add to the mix 1g of lime for every 2g of MHRB used. (IE: 75g lime for 150g MHRB) More lime will not hurt, it tends to make a slightly better consistency if it is closer to 1g lime per 1g MHRB, though if your lime stock is low just do 1g lime per 2g MHRB
-Start stirring and it should get pretty dry, add some boiling water a little splash at a time until it is gooey/easy to stir but not watery. DO IT SLOWLY. You can add more later, you can't instantly evaporate 20ml of water though.
-As long as it is mixed and stays warm (by replacing the water below periodlically) it should only take a 2-5 hours for 99% the alkaloids to freebase.
Note: The mix will form a "dark crust" that is fine. It does not affect the yield at all, it is a sign you are doing the tek right! It will actually tell you when most of the alkaloids are out. When there is no DMT left, the mix will not crust, but just stay dark!
If using the 100% food safe alternative method, scroll down to the big "100% food safe* and proceed with the "for full alkaloids"
Non-Polar Wash:
This step is to use naptha to dissolve the DMT and separate it from all that other gunk.
