Difference between revisions of "Machine-Style Bubbler Stem"

From DMT-Nexus Wiki
Jump to: navigation, search
m
(fixed notes)
Line 5: Line 5:
 
|the Improvisation of the [[Machine-Style Bubbler Stem]]<ref>[[The Mini-Machine Bubbler Stem]]</ref><ref>[[The Inspirator]]</ref>
 
|the Improvisation of the [[Machine-Style Bubbler Stem]]<ref>[[The Mini-Machine Bubbler Stem]]</ref><ref>[[The Inspirator]]</ref>
 
|
 
|
−
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|This variation can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers, though smaller bubblers are often found most preferable.
+
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|A design of bubbler or piece that facilitates being angled in such a way that the product can only runo toward the heat-source is preferable to ensure full dosage; however, the use of a better heat-sink, such as ceramic fiber, in conjunction with the metal mesh as a screen will prevent such problems at any angle.
 
|0px
 
|0px
 
|
 
|
Line 14: Line 14:
 
# Cut off a piece of the metal scrub pad, hold it with pliers, and burn with a torch under an oven hood until no more smoke is emitted.
 
# Cut off a piece of the metal scrub pad, hold it with pliers, and burn with a torch under an oven hood until no more smoke is emitted.
 
# After it has cooled, stuff it in the larger end of the piece, and stuff it down toward the end designated for heat application somewhat tightly, and so that a part of the mesh is exposed.
 
# After it has cooled, stuff it in the larger end of the piece, and stuff it down toward the end designated for heat application somewhat tightly, and so that a part of the mesh is exposed.
−
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|The water in the bubbler acts only as a heat-sink and will not absorb a significant, if any, amount of product, as the freebase product is not very soluble in water; however, the use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.
+
{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|Most designs will result in runoff if used at a downward angle, but if a straight glass piece is used, that runoff may be immediately retrievable for further administration by simply plunging the plug to one end of the piece, then back into place.
 
|0px
 
|0px
 
|
 
|
 
}}
 
}}
 
{{ShowInfo/In Article|[[Image:Information.png]]|Notes on Administration|
 
{{ShowInfo/In Article|[[Image:Information.png]]|Notes on Administration|
−
* To load, simply place a measured dose inside the piece push on the plug and carefully melt into the plug by feathering with a flame or other heat source.
+
* To load, simply place a measured dose inside the piece and onto the plug, and carefully melt into the plug by feathering with a flame or other heat source.
 
* A butane torch is a preferable heat source for the operation of this piece.
 
* A butane torch is a preferable heat source for the operation of this piece.
 
|0px
 
|0px

Revision as of 23:03, 21 January 2010

Note error.png Note: This page has been transcluded to The Nexian DMT Handbook under the Machine-Style Bubbler Stem section or other locations within or without the handbook. Please markup in consideration of this. The top section header is to remain in place as a reference for subsequent section headers and to allow easy editing directly from the handbook.


the Improvisation of the Machine-Style Bubbler Stem[1][2] Cog.png
NOTE Information.png
A design of bubbler or piece that facilitates being angled in such a way that the product can only runo toward the heat-source is preferable to ensure full dosage; however, the use of a better heat-sink, such as ceramic fiber, in conjunction with the metal mesh as a screen will prevent such problems at any angle.
A Machine-Style Bubbler Stem seated in a bubbler.
  1. Prepare a glass piece to be fitted to the intake of a bubbler.
    • this can be accomplished either by using a glass piece small enough to fit inside with a gasket fitted to provide a seal or by attaching the piece with a small section of tubing.
  2. Cut off a piece of the metal scrub pad, hold it with pliers, and burn with a torch under an oven hood until no more smoke is emitted.
  3. After it has cooled, stuff it in the larger end of the piece, and stuff it down toward the end designated for heat application somewhat tightly, and so that a part of the mesh is exposed.
NOTE Information.png
Most designs will result in runoff if used at a downward angle, but if a straight glass piece is used, that runoff may be immediately retrievable for further administration by simply plunging the plug to one end of the piece, then back into place.
Notes on Administration Information.png
  • To load, simply place a measured dose inside the piece and onto the plug, and carefully melt into the plug by feathering with a flame or other heat source.
  • A butane torch is a preferable heat source for the operation of this piece.


Reference
  1. ↑ The Mini-Machine Bubbler Stem
  2. ↑ The Inspirator
Retrieved from "https://wiki.dmt-nexus.me/w/index.php?title=Machine-Style_Bubbler_Stem&oldid=2393"