Dry Technique Extraction

From DMT-Nexus Wiki
Revision as of 22:44, 22 December 2009 by Amor fati (Talk | contribs)

Jump to: navigation, search
Note error.png Note: This page has been transcluded to The Nexian DMT Handbook under the Dry Technique Extraction section or other locations within or without the handbook. Please markup in consideration of this. The top section header is to remain in place as a reference for subsequent section headers and to allow easy editing directly from the handbook.


Dry Technique Extraction

Note error.png Note: This technique is still experimental and may result in variable success if used with MHRB.

Dry techniques (drytek) evolved from and are ideally intended for the implementation of the FASA method of crystallization and serve as the only techniques able to implement acetone as an extraction solvent. Acetone is generally favored for its ability to extract a notably broad range of active products.

Considerations:

The use of dry techniques requires fewer and less toxic materials than the techniques that employ aqueous phases and separatory methods. The materials required are generally of a more household nature. They are most effectively applied to powdered botanical material. Acetone is, however, completely water miscible, so proper drying procedures are of the utmost importance. This technique may or may not require the defatting of botanical materials, depending on the intended method of crystallization. Dry techniques are the youngest of the current extraction techniques though apparently sound in theory and in practice.


Overview of Materials and Methods
Materials Required Checklist.png
Source Material:
  • Powdered DMT-Containing Botanical Material
Solvents:
  • Water
  • Acetone
Reagents/Desiccants:
  • Magnesium Sulfate (Epsom Salt)
  • Household Base:
    • Either Sodium Carbonate (Washing Soda)
    • or Calcium Hydroxide (Pickling Lime)
    • or Sodium Bicarbonate (Baking Soda)



Material Considerations:

  • Acetone can be purchased at hardware stores but should be confirmed as pure acetone prior to purchase. Note that almost all acetone can contain up to 5% water contamination, depending on time and shelving conditions.
  • In order to be utilized for extraction, sodium bicarbonate must undergo conversion to sodium carbonate.
  • Lime is often found difficult to decant acetone off of and also difficult to filter out of acetone, whereas sodium carbonate is generally found more agreeable for both.
  • Distilled water is preferable, as tap water almost always contains impurities that can potentially tamper with resulting yields.
  • With few exceptions, the source material should be completely pulverized to a powder consistency before use, as this technique's choice of reagents are not quite capable of penetrating cell structure.

Methods:

Extractions by dry techniques are characterized by the lack of a traditional aqueous phase in the extraction process, and instead, opting for basification within a paste which is followed by chemically drying the paste with desiccant. The process does not make use of separatory methods, and instead is characterized by it's use of dry-washing, decanting and non-intensive filtering methods. Certain materials must be rendered anhydrous prior to use.


Material Preparation
Rendering Anhydrous Magnesium Sulfate Cog.png
  1. Spread Epsom Salt (Hydrated Magnesium Sulfate) on an aluminum foil covered pan.
  2. Place in the oven on 400°F for about one hour, or until the salt becomes gray and ash-like.
  3. Place your now anhydrous magnesium sulfate into a storage container and store away from moisture.
  4. If it becomes hydrated again, the process can be repeated.
  • This can also be done on the stove top/oven ring, however it should be noted that as the Epsom Salt looses water it will stick to the inside of your pot but as it reaches complete dehydration and becomes grey and ash like it will unstick and become a powder.


Rendering Anhydrous Acetone Cog.png
  1. Pour anhydrous magnesium sulfate directly into the can of acetone.
  2. Shake vigorously for an extended amount of time.
  3. Allow to settle for one day.
  4. Observe the magnesium sulfate at the bottom of the can.
    • If it appears extremely moist, repeat the process
    • If it appears quite dry, the acetone is ready for use.
  5. Store away from moisture and never leave sitting with the cap off.


Conversion of Sodium Bicarbonate into Sodium Carbonate Cog.png
  1. Pour sodium bicarbonate onto a non-aluminum pan.
  2. Place in the oven at 400ºF for one hour
  3. Place in a storage container and store away from moisture.
  • This can also be done on a stove top/oven ring in a pot and take around 5-10 minutes to completely dehydrate (it becomes a fine light white powder and the CO2 stops bubbling through the powder).


Extraction Procedure
  1. Mix the intended base with the powdered source material at a ratio between 1:2 and 1:1.
    • The product remains in its natural salt form which is generally considered to be quite free from the botanical cell structure in powdered material.
  2. Add only enough water to thoroughly moisten the mixture to the consistency of a paste while stirring to ensure the consistency of the mixture.
    • Although this is not generally considered a traditional aqueous phase in that it is not a solution, it is an aqueous phase in that it is excessively hydrated and sufficiently aqueous to facilitate reaction.
  3. Allow adequate time to soak in order for reaction to occur.
    • The acid component of salt-form product undergoes reaction with the base, effectively neutralizing the acid and freeing the product in its pure alkaloid form, or freebase.
  4. Stir in anhydrous magnesium sulfate until thoroughly dry.
    • The magnesium sulfate acts as a desiccant, and that this is performed in order to prevent water contamination of the acetone.
  5. Add an excess of anhydrous acetone and stir thoroughly, allotting adequate time and stirring for thorough dissolution of the product into the acetone.
    • The more contact allotted between the product and the acetone, the greater the saturation.
  6. Decant and/or filter acetone and collect, being careful not to allow any particulates into the collection vessel.
    • The bases used should not harm the quality of the product, but may interfere with the accuracy of weight.
  7. Repeat steps 5-6 with fresh acetone until material is exhausted to satisfaction.
    • Three washes is generally considered sufficient.