Difference between revisions of "House's cacti preparation tek"
(→Pictures) |
|||
| Line 43: | Line 43: | ||
Step 1 - Get the water boiling, toss in the cacti and add citric acid and bring to a simmer. | Step 1 - Get the water boiling, toss in the cacti and add citric acid and bring to a simmer. | ||
| − | + | http://i33.tinypic.com/2uz6u88.jpg | |
Keep simmering it. The water will turn into a nice dark brown. Add water as necessary. | Keep simmering it. The water will turn into a nice dark brown. Add water as necessary. | ||
| − | + | http://i34.tinypic.com/25rhycw.jpg | |
Step 2 - Filter the cacti from the water and pour it into a pyrex pan. | Step 2 - Filter the cacti from the water and pour it into a pyrex pan. | ||
| − | + | http://i38.tinypic.com/npkivr.jpg | |
Step 3 - Put it in an oven to evap or in the open air, using a fan is recommended. | Step 3 - Put it in an oven to evap or in the open air, using a fan is recommended. | ||
| − | + | http://i36.tinypic.com/2qwdkxu.jpg | |
Make it into a nice thick resin by moving it around to let it breathe. At this point it's going to be very liquidy, it's recommended to put it in the oven until it completely hardens. | Make it into a nice thick resin by moving it around to let it breathe. At this point it's going to be very liquidy, it's recommended to put it in the oven until it completely hardens. | ||
| − | + | http://i34.tinypic.com/2yxetli.jpg | |
Put in lots of your energy and swirl it around. The idea is to let oxygen into all parts of the mixture. | Put in lots of your energy and swirl it around. The idea is to let oxygen into all parts of the mixture. | ||
| − | + | http://i33.tinypic.com/1zocjso.jpg | |
Soon, it will become quite hard and easy to work with. This is when you want to cap it. Be careful not to handle it too much as your hands will heat up the resin and make it sticky again. | Soon, it will become quite hard and easy to work with. This is when you want to cap it. Be careful not to handle it too much as your hands will heat up the resin and make it sticky again. | ||
| − | + | http://i33.tinypic.com/xlkvex.jpg | |
The result! | The result! | ||
Revision as of 05:18, 1 November 2009
 |
Note: | This page is a transcription of "The Way" Cacti Resin Tek[1]. The content is to remain accurate as such. |
Did you know you can evaporate your filtered san pedro tea (ie: oven@150F or food dehydrator) to yield a resin that is easily scraped up with your fingers and rolled into capsules? (It has a Taffy-like consistency)
This resin is far superior to pure extracted mescaline.
There's so much more to it...you gotta see for yourself.
This is golden, glowing, soul food.
You can get far more out of your cacti this way.
Step 1
Just simply simmer or crock pot your pedro chunks (sliced like food) with lemon juice (One lemon squeezed) for as long as you want. Anywhere from a few hours to a day.You can even freeze/thaw your pedro before hand to break down the cell walls.
Step 2
Once cooked, filtered, you reduce in the oven or food dehydrator to acquire this resin medicine.
Administration
Jorkest and I estimate there is at least 70mg mescaline in each 00 cap of resin.
5 caps is entheogenic bliss. You can feel it's healing effects well throughout the week with every toke, every mocha
Seriously don't waste your time with mescaline crystals, work with the spirit of san pedro it might change your life this method has mine!
Effects
I would describe it's effects like an organic "candy flip" (slang for LSD+MDMA) while remaining comfortable and lucid. Deep emotional healing, and strength are acquired. Even spectacular with caapi. Needless to say, I'll never eat molly again.
Reference
Pictures
The following pictures were taken by SWIM.
Step 1 - Get the water boiling, toss in the cacti and add citric acid and bring to a simmer. http://i33.tinypic.com/2uz6u88.jpg
Keep simmering it. The water will turn into a nice dark brown. Add water as necessary. http://i34.tinypic.com/25rhycw.jpg
Step 2 - Filter the cacti from the water and pour it into a pyrex pan. http://i38.tinypic.com/npkivr.jpg
Step 3 - Put it in an oven to evap or in the open air, using a fan is recommended. http://i36.tinypic.com/2qwdkxu.jpg
Make it into a nice thick resin by moving it around to let it breathe. At this point it's going to be very liquidy, it's recommended to put it in the oven until it completely hardens. http://i34.tinypic.com/2yxetli.jpg
Put in lots of your energy and swirl it around. The idea is to let oxygen into all parts of the mixture. http://i33.tinypic.com/1zocjso.jpg
Soon, it will become quite hard and easy to work with. This is when you want to cap it. Be careful not to handle it too much as your hands will heat up the resin and make it sticky again. http://i33.tinypic.com/xlkvex.jpg
The result! File:Http://i33.tinypic.com/10fszzo.jpg
