Machine-Style Bubbler Piece - Revision history

TheTraveler: Text replace - "dmt-nexus.com" to "dmt-nexus.me"

2012-01-31T19:56:34Z

Text replace - "dmt-nexus.com" to "dmt-nexus.me"

2010-04-13T17:46:18Z

‎Machine-Style Bubbler Piece

2010-04-08T15:06:45Z

2010-04-08T15:05:34Z

2010-04-08T15:04:36Z

‎Machine-Style Bubbler Piece: replaced photo

2010-01-26T23:37:28Z

‎Machine-Style Bubbler Piece

2010-01-25T18:56:23Z

‎Machine-Style Bubbler Piece

2010-01-25T18:40:12Z

2010-01-25T18:38:35Z

2010-01-25T18:36:40Z

@@ Line 10: / Line 10: @@
 {{procedure
-|the Improvisation of the Bubbler Bowl Variation of "[[The Machine]]"<ref>Posts Regarding Construction and Operation of a Machine-Style Bubbler Bowl by WSaged[http://www.dmt-nexus.com/forum/default.aspx?g=posts&m=91587#post91587][http://dmt-nexus.com/forum/default.aspx?g=posts&m=92032#post92032][http://dmt-nexus.com/forum/default.aspx?g=posts&m=68006#post68006][http://www.dmt-nexus.com/forum/default.aspx?g=posts&m=109586#post109586]</ref>
+|the Improvisation of the Bubbler Bowl Variation of "[[The Machine]]"<ref>Posts Regarding Construction and Operation of a Machine-Style Bubbler Bowl by WSaged[http://www.dmt-nexus.me/forum/default.aspx?g=posts&m=91587#post91587][http://dmt-nexus.me/forum/default.aspx?g=posts&m=92032#post92032][http://dmt-nexus.me/forum/default.aspx?g=posts&m=68006#post68006][http://www.dmt-nexus.me/forum/default.aspx?g=posts&m=109586#post109586]</ref>
+|
 {{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|This design differs from "the machine" slightly in that it does not consistently protect the product from open flame.

@@ Line 3: / Line 3: @@
 ====== [[Machine-Style Bubbler Piece]] ======
-{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|Theses variations can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers, though smaller bubblers are often found most preferable.  The water in the bubbler acts only as a heat-sink and will not absorb a significant, if any, amount of product, as the freebase product is not very soluble in water; however, the use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.
+{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|Theses variations can apply to the use of a small bubbler pipes, bong-style bubblers, or improvised bubblers, though smaller bubblers are often found most preferable.  The water in the bubbler acts only as a heat-sink and will not absorb a significant, if any, amount of product, as the freebase product is not soluble in water; however, the use of ice in cooling should be forgone, as it may cause the premature precipitation of product within the chamber.
 |0px
+|

@@ Line 27: / Line 27: @@
 {{ShowInfo/In Article||Notes on Administration|
 * To load, simply place a measured dose directly on top of the plug and carefully melt into the plug by feathering with a flame or other heat source.
-* Though a standard lighter will work for vaporizing if used carefully, a torch may ensure a fuller dose--though at a slightly higher risk for overheating and burning if any spice remains on the surface.
+* A standard lighter will work adequately for this style of device.
 |0px
+|

@@ Line 25: / Line 25: @@
 #* ''if using a small thin tube of mesh, stuff the end tightly in the bowl and coil loosely around the inside, leaving about a quarter inch of space between the coil and the lip.''
 #* ''the plug needs to be tight enough to suspend it in the opening but not so tight as to block air passage.''
 {{ShowInfo/In Article||Notes on Administration|
 * To load, simply place a measured dose directly on top of the plug and carefully melt into the plug by feathering with a flame or other heat source.

@@ Line 16: / Line 16: @@
+|
 }}
-[[Image:Machine-Style Bubbler Bowl.jpg|thumb|right|A Crude Variation of a Machine-Style Bubbler Bowl being loaded.]]
+[[Image:Machine_bowl.JPG|thumb|right]]
 # Prepare a plug made of metal mesh by cutting a piece of an excess of the appropriate size to fit in the bowl.
 #* ''stainless steel and copper of a coarse mesh are preferable, as they do not tend to burn at the temperatures needed for vaporization.''

@@ Line 12: / Line 12: @@
 |the Improvisation of the Bubbler Bowl Variation of "[[The Machine]]"<ref>Posts Regarding Construction and Operation of a Machine-Style Bubbler Bowl by WSaged[http://www.dmt-nexus.com/forum/default.aspx?g=posts&m=91587#post91587][http://dmt-nexus.com/forum/default.aspx?g=posts&m=92032#post92032][http://dmt-nexus.com/forum/default.aspx?g=posts&m=68006#post68006]</ref>
+|
-{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|This variation differs from "the machine" slightly in that it does not consistently protect the product from open flame.
+{{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|This desigh differs from "the machine" slightly in that it does not consistently protect the product from open flame.
 |0px
+|

@@ Line 23: / Line 23: @@
 #* ''perform this step until no more smoke can be observed emanating from the cutting.''
 # Allow to cool and roll the cutting tight enough to fit in the bowl.
-#* ''if using a small thin tube of mesh, stuff the end tightly in the bowl and coil loosely around the inside.''
+#* ''if using a small thin tube of mesh, stuff the end tightly in the bowl and coil loosely around the inside, leaving about a quarter inch of space between the coil and the lip.''
 #* ''the plug needs to be tight enough to suspend it in the opening but not so tight as to block air passage.''
 {{ShowInfo/In Article|[[Image:Information.png]]|'''NOTE'''|Use of this variation is often found to result in runoff down the stem of the bowl, which is only retrievable by cleaning the bowl, and it is also found difficult to prevent the burning of product due to exposure.  However, many of these potential problems are avoidable by mastery of heating and calibration of airflow through the piece.