DIY vacuum filtration system - Revision history

--Shadow at 13:26, 1 May 2014

2014-05-01T13:26:35Z

--Shadow at 12:18, 30 April 2014

2014-04-30T12:18:03Z

--Shadow: /* Step Three */

2014-04-30T12:16:49Z

‎Step Three

--Shadow: /* Step Five */

2014-04-30T12:10:43Z

‎Step Five

--Shadow: /* Step Three */

2014-04-30T12:09:25Z

‎Step Three

--Shadow: /* Step Three */

2014-04-30T12:03:50Z

‎Step Three

--Shadow: Created page with " ==Introduction== All equipment can be obtained from Bunning's ==Required Equipment== * Suction pump drain cleaner * 25mm x 90cm Clear vinyl tubing * 17-32mm Stainless ste..."

2014-04-30T12:02:17Z

Created page with " ==Introduction== All equipment can be obtained from Bunning's ==Required Equipment== * Suction pump drain cleaner * 25mm x 90cm Clear vinyl tubing * 17-32mm Stainless ste..."

New page

==Introduction==

All equipment can be obtained from Bunning's

==Required Equipment==

* Suction pump drain cleaner
* 25mm x 90cm Clear vinyl tubing
* 17-32mm Stainless steel hose clamp
* Some Rubber bands
* Funnel

[[File:Equipment_drain_pump.jpg|400px|Required Equipment]]

==Step One==
Unscrew suction piece off the drain pump.

[[File:DIY_vacuumfilter_pump.jpg|400px]]

==Step Two==
Wind a few rubber bands around the tip of the drain pump - this will ensure an airtight fit when the clamp is tightened.

[[File:DIY_vacuumfilter_pump_2.jpg|400px]]

==Step Three==
Fit the clear tubing onto the pump.

[[File:DIY_vacuumfilter_pump_3.jpg|400px]]

==Step Four==
Screw the steel clamp on tight.

[[File:DIY_vacuumfilter_pump_4.jpg|400px]]

==Step Five==
Place in bucket and fit the funnel into the end of the hose. The hose should be flat along the bottom of the bucket, which holds the hose stable when the funnel is full.

[[File:DIY_vacuumfilter_pump_5.jpg|400px]]

[[Category:Tek]]

← Older revision		Revision as of 13:26, 1 May 2014
Line 46:		Line 46:
	To create the one-way pump, hold your finger over the "Shottie" hole when pulling, then take your finger off when flowing pushing the pump back in.		To create the one-way pump, hold your finger over the "Shottie" hole when pulling, then take your finger off when flowing pushing the pump back in.

−	[[Category:Tek]]	+	[[Category:Administration Tek]]

@@ Line 3: / Line 3: @@
 ==Introduction==
-All equipment can be obtained from Bunning's
+Here's a DIY guide on creating your very own vacuum filtration system. All equipment can be obtained from Bunning's
 ==Required Equipment==
@@ Line 43: / Line 43: @@
 [[File:DIY_vacuumfilter_pump_5.jpg|400px]]
+==Usage==
-To create the one-way pump, hold your finger over the "Shottie" hole when pulling, then take your finger off when flowing pushing the pump back in
+To create the one-way pump, hold your finger over the "Shottie" hole when pulling, then take your finger off when flowing pushing the pump back in.
 [[Category:Tek]]

@@ Line 31: / Line 31: @@
 [[File:DIY_vacuumfilter_pump_2b.JPG|400px]]
-[[File:DIY_vacuumfilter_pump_3.jpg|400px]]
+[[File:DIY_vacuumfilter_pump_3.jpg|370px]]
 ==Step Four==

← Older revision		Revision as of 12:10, 30 April 2014
Line 42:		Line 42:

	[[File:DIY_vacuumfilter_pump_5.jpg\|400px]]		[[File:DIY_vacuumfilter_pump_5.jpg\|400px]]
		+
		+
		+	To create the one-way pump, hold your finger over the "Shottie" hole when pulling, then take your finger off when flowing pushing the pump back in

	[[Category:Tek]]		[[Category:Tek]]

@@ Line 28: / Line 28: @@
 ==Step Three==
-Fit the clear tubing onto the pump.
+Burn or cut a small "shottie" hole near the tip of the clear tube, then fit the clear tubing onto the pump.
 [[File:DIY_vacuumfilter_pump_3.jpg|400px]]